To set up the fw-1884 in Cubase or Nuendo 3 To set up the fw-1884 in Mackie Emulation protocol 3




Download 141.3 Kb.
NameTo set up the fw-1884 in Cubase or Nuendo 3 To set up the fw-1884 in Mackie Emulation protocol 3
A typeDocumentation
manual-guide.com > manual > Documentation
FW-1884
Professional Control Surface / FireWire Audio-MIDI Interface
Cubase SX/SL / Nuendo (Windows/Mac) NOTES
Table of Contents
Setup 3

To set up the FW-1884 in Cubase or Nuendo 3 To set up the FW-1884 in Mackie Emulation protocol 3
Emulation mapping 4
EQ (Mackie Control Mode) 5

Encoder settings 5
Shortcuts Section 6

Function/Automation Keys 7

Footswitch 7

2 TASCAM FW-1884

Cubase SX/SL / Nuendo (Win/Mac)

The FW-1884 controls Steinberg’s Cubase SX, Cubase SL and Nuendo using the Mackie Control or Mackie HUI emulation protocols. (HUI emulation notes can be found in a separate document). Cubase and Nuendo “see” the FW-1884 as a Mackie Control in their Device

menus. This section describes the mapping of the FW-1884’s control surface in Mackie Control Emulation protocol, and how this mapping corresponds to the controls in Cubase and Nuendo. It is not intended as a guide to basic recording or to working with Cubase or Nuendo. For more detailed information on the functional operation of Cubase or Nuendo, please refer to the Steinberg manuals for these programs.
The FW-1884 is only supported by versions of Cubase and Nuendo which support the Mackie Control. It is not supported under earlier versions of Cubase, including Cubase VST. This implementation corresponds as much as possible to the Mackie Control mapping as implemented by Steinberg. It is not a generic implementation.

Setup
To set up the FW-1884 in Cubase or Nuendo

1 In the Devices menu, select Device Setup

2 Click the Add/Remove tab
3 Select Mackie Control from the list of available devices, and click the Add button.
4 Click the Setup tab
5 Locate the Mackie Control on the list of installed devices and highlight it by clicking on it once.
6 Select FW-1884 Control for both MIDI Input and MIDI Outputs.
Click ok.
Do not select both the Mackie Control and the Mackie hui at the same time. This will cause incorrect operation of the FW-1884 if the fw-1884 Control is selected for midi Input and midi Output.
To set up the FW-1884 in Mackie Emulation protocol

In the drop-down Control Protocol menu, select Mackie Control Emulation.

1 Open the FW-1884 Control Panel

2 Select the Settings tab
3 TASCAM FW-1884

Cubase SX/SL / Nuendo (Win/Mac): Emulation mapping

Emulation mapping
Below is a description of Mackie Control emulation mapping within Cubase / Nuendo.
Channel Strips The eight channel strips and the master fader on the FW-1884 map directly to the eight channel strips and master fader on the Mackie Control. The MUTE and SOLO keys and the faders are identical in function. In many cases, the FW-1884 uses the REC key as a modifier; for example, holding the REC key and pressing a channel SELect key on the FW-1884 will emulate pressing a corresponding REC/RDY key on the Mackie Control. To emulate pressing a Mackie Control push-key rotary encoder, press and hold the REC key and press the channel SOLO key on the FW1884.
The following table summarizes the channel strip mappings. For this and all subsequent tables in this section:
y – means yes, the key or indicator on the Mackie Control is mapped to the FW-1884.
n – means no, the key or indicator on the Mackie Control is not mapped to the FW-1884.
n/a – means there is no key or indicator for that function (for example, a fader move).

FW-1884

Cubase/Nuendo

Key

Light

Fader move

Fader move

n/a

n/a

Touch sensor

Touch sensor

y

n/a

MUTE

MUTE

y

y

SOLO

SOLO

y

y

SELECT

SELECT

y

y

REC light

REC (ch rec enable)

n/a

y

REC + SELECT

REC (ch rec enable)

y

n/a

Encoder turn

Encoder turn

n/a

n/a

CTRL + SEL

Encoder press

y

n/a



FW-1884

Cubase/Nuendo

Key

Light

F FWD

FAST FWD

y

y

STOP

STOP

y

y

PLAY

PLAY

y

y

RECORD

RECORD

y

y

CTRL + RECORD

PI

y

y

^BANK


y

-

BANK^

BANK>

y

-

Data wheel turns

Data wheel turns

-

-

SHUTTLE

SHUTTLE

y

y

?

UP

y

-

T

DOWN

y

-

M

LEFT

y

-

?

RIGHT

y

-

SET

ZOOM

y

-

¦« LOCATE

PO

y

n

LOCATE ??

END

y

n

IN


y

n

OUT

FRM>

y

n

^NUDGE

LEFT (cursor)

y

n

NUDGED

RIGHT (cursor)

y

n


Assignment Section At the top left of the FW1884 are its illuminated ENCODERS keys. These emulate the Mackie Control ASSIGNMENT and DISPLAY keys and indicators as shown below.
PAN uses the channel encoders to set both left/right and front/rear pan position.
Transport Controls Most transport functions are identical between the Mackie Control and the FW1884. The FW-1884 has no ZOOM key and indicator, so the SET key is used in its place.

FW-1884
Cubase/Nuendo Key Light

y

y

REW

REWIND

Since the FW-1884 does not have a scribble strip display, the operator must use the applications Mixer window as a visual reference for the following functions.
1 Press PAN and AUX 3 if necessary (this is the normal default) to set left/right pan.
2 Press AUX 4 (page-up) to set front/rear position in a surround mix.
4 TASCAM FW-1884

Cubase SX/SL / Nuendo (Win/Mac): EQ (Mackie Control Mode)

EQ (Mackie Control Mode)
1 Press AUX 2 to enable EQ adjustment mode on the FW-1884.
2 Press AUX 3 (page down) to set Frequency and Gain adjustment for all 4 bands using the channel encoders. Encoders 1-8 correspond as follows:
l=Lo Freq 2=Lo Gain 3=Lo-Mid Freq 4=Lo-Mid Gain 5=Hi-Mid Freq 6=Hi-Mid Gain

7=Hi-Freq 8=Hi Gain
Press AUX 4 (page up) to enable/disable and set the Qfor each band. Encoders 1-8 correspond as follows:
l=Lo on/off 2=LoQ

3=Lo-Mid on/off 4=Lo-Mid Q 5= Hi-Mid on/off 6=Hi-Mid Q 7=Hi on/off 8=Hi-Q.
Encoder settings
AUX 3 and 4 function as "Page Down" and "Page Up" controls for features that would otherwise use multiple "Pages" of encoder settings displayed on a scribble strip. These functions include Pan, EQ, Sends levels and effects, Insert Plug-Ins, Sends effects parameters, VST Instrument parameters, Master effects parameters.
The functions below are multi-page functions that are best used while viewing the appropriate panel in the DAW display. Use the Aux 3 and Aux 4 buttons as described above to navigate the various pages.
AlIX 5 uses the channel encoders to set 'SENDS' levels.
Page 1 - Level for sends 1 through 8 on FW1884 encoders 1 - 8.

Page 2 - Send on/off for sends 1 through 8. Page 3 - Send pre/post for sends 1 through 8. Page 4 - Effects bus select for effects busses 1 through 8.
AlIX 6 uses channel encoders to set "Insert" Plug-In parameters.
Page 1 - Select Insert #, Insert on/off, Effect type (encoders 3-5), encoders 6-8 not used
Page 2 - various effect parameters dependent on effect type selected above

Page 3 - continuation of page 2. Actual number of pages will depend on effect type.
F8 Uses channel encoders to set parameters of the effect chosen by Aux 5 (Sends).
Page 1 - Select Send #, Effect on/off, encoders 38

not used

Page 2 - various effect parameters dependent on

effect type selected above

Page 3 - continuation of page 2. Actual number

of pages will depend on effect type.
F9 Uses channel encoders to set parameters of VST Instruments.
Page 1 - VST Instrument #, on/off, encoders 3-8

not used

Page 2 - various parameters dependent on

instrument type selected above

Page 3 - continuation of page 2. Actual number

of pages will depend on instrument.

5 TASCAM FW-1884
Cubase SX/SL / Nuendo (Win/Mac): Shortcuts Section

F10 Uses channel encoders to set parameters of the Master effects chosen on the Master Effects panel.
Page 1 - Master effects #, on/off, encoders 3-8

not used

Page 2 - various effect parameters dependent on

effect type selected above

Page 3 - continuation of page 2. Actual number

of pages will depend on effect type.

FW-1884

Cubase/Nuendo

Key

Light

FLIP

FLIP

y

y

PAN

PAN

y

y

AUX1

EDIT

y

y

AUX 2

EQ

y

y

AUX 3

I/O

y

y

AUX 4

SENDS

y

y

AUX 5

DYN

y

y

AUX 6

PLUG-INS

y

y

CTRL +< BANK


y

-

CTRL+BANK^

CHANNEL>

y

-


Shortcuts Section

At the bottom left of the FW-1884 are its fourteen illuminated SHORTCUTS keys. These emulate the fourteen keys in the MODIFIERS, AUTOMATION, and FUNCTIONS sections on the Mackie Control, as shown here:

FW-1884

Cubase/Nuendo

Key

Light

SAVE/F1

CONTROL

y

y

REVERT/F2

ALT

y

-

ALL SAFE/F3

N/A







CLR SOLO/F4

SOLO DEFEAT

y

-

MARKER/F5

MARKER

y

y

LOOP/F6

LOOP

y

y

CTRL+UNDO

REDO

y

y

CUT

F1

y

y



FW-1884

Cubase/Nuendo

Key

Light

DELETE

F2

y

y

COPY

F3

y

y

PASTE

F4

y

y

CTRL+CUT

F5

y

y

CTRL + DELETE

F6

y

y

CTRL + COPY

F7

y

y

CTRL + PASTE

F8

y

y

ALT/CMD

n/a

y

-

UNDO

UNDO

y

-

SHIFT

N/A

y

y

CTRL

N/A

y

-


6 TASCAM FW-1884
Cubase SX/SL/ Nuendo (Win/Mac): Shortcuts Section

Function/Automation Keys
Above the FW-1884's main transport keys are eight illuminated keys which can be used to emulate pressing various Mackie Control function and editing keys. This implementation allows you access to various functions within Cubase/Nuendo, including some not silkscreened on the FW-1884's surface.

FW-1884

Cubase/Nuendo

Key

Light

F7

MOTORS

y

-

F8

SENDS

y

-

F9

VSTi

y

-

F10

MASTER FX

y

-

READ

READ

y

-

WRT

WRITE

y

-



FW-1884

Cubase/Nuendo

Key Light

TCH

PROJECT

y

LATCH

MIXER

y

CTRL+F7

F9

y

CTRL+F8

F10

y

CTRL+F9

F11

y

CTRL+F10

F12

y

CTRL +READ

F13

y

CTRL +WRT

F14

y

CTRL +TCH

F15

y

CTRL +LATCH

F16

y



Footswitch
USER SWITCH A and B are the two footswitch inputs on the back of the Mackie Control.



FW-1884

Cubase/Nuendo

Key

Light

Footswitch

USER SWITCH A

y

-

CTRL +

Footswitch

USER SWITCH B

y





7 TASCAM FW-1884
TASCAM

TEAC Professional Division

FW-1884
TEAC CORPORATION

Phone: +81-422-52-5082

3-7-3, Nakacho, Musashino-shi, Tokyo 180-8550, Japan

www.tascam.com

TEAC AMERICA, INC. Phone: +1-323-726-0303 7733 Telegraph Road, Montebello, California 90640

www.tascam.com

TEAC CANADA LTD.

Phone: +1905-890-8008 Facsimile: +1905-890-9888

5939 Wallace Street, Mississauga, Ontario L4Z 1Z8, Canada

www.tascam.com

TEAC MEXICO, S.A. De C.V

Phone: +52-555-581-5500

Campesinos No. 184, Colonia Granjes Esmeralda, Delegaacion Iztapalapa CP 09810, Mexico DF

www.tascam.com

TEAC UK LIMITED

Phone: +44-1923-438880

5 Marlin House, Croxley Business Park, Watford, Hertfordshire. WD1 8TE, U.K.

www.tascam.co.uk

TEAC DEUTSCHLAND GmbH

Phone: +49-611-71580

Bahnstrasse 12, 65205 Wiesbaden-Erbenheim, Germany

www.tascam.de

TEAC FRANCE S. A.

Phone: +33-1-42-37-01-02

17 Rue Alexis-de-Tocqueville, CE 005 92182 Antony Cedex, France

www.tascam.fr

TEAC AUSTRALIA PTY.,LTD. A.B.N. 80 005 408 462 Phone: +61-3-9672-2400 Facsimile: +61-3-9672-2249 280 William Street, Port Melbourne, Victoria 3000, Australia

www.tascam.com.au

TEAC ITALIANA S.p.A. Phone: +39-02-66010500 Via C. Cantu 11, 20092 Cinisello Balsamo, Milano, Italy

www.teac.it

Share in:

Related:

To set up the fw-1884 in Cubase or Nuendo 3 To set up the fw-1884 in Mackie Emulation protocol 3 iconPhp version: 17 set foreign key checks=0; set sql mode="no auto value...

To set up the fw-1884 in Cubase or Nuendo 3 To set up the fw-1884 in Mackie Emulation protocol 3 iconFw-1884 Quick Start Guide

To set up the fw-1884 in Cubase or Nuendo 3 To set up the fw-1884 in Mackie Emulation protocol 3 iconDG102sh console Command Set(set coding, set h323, and show)

To set up the fw-1884 in Cubase or Nuendo 3 To set up the fw-1884 in Mackie Emulation protocol 3 iconResearch into an Intermediate Accounting level practice set was conducted....

To set up the fw-1884 in Cubase or Nuendo 3 To set up the fw-1884 in Mackie Emulation protocol 3 iconHome Station (Client) Set-up and use Client Set-up

To set up the fw-1884 in Cubase or Nuendo 3 To set up the fw-1884 in Mackie Emulation protocol 3 iconThe Thymatron® instrument separates stimulus dose from pulsewidth...

To set up the fw-1884 in Cubase or Nuendo 3 To set up the fw-1884 in Mackie Emulation protocol 3 iconHow to set up a ddns

To set up the fw-1884 in Cubase or Nuendo 3 To set up the fw-1884 in Mackie Emulation protocol 3 icon2Initial Set Up

To set up the fw-1884 in Cubase or Nuendo 3 To set up the fw-1884 in Mackie Emulation protocol 3 iconP roduct Set-Up Information

To set up the fw-1884 in Cubase or Nuendo 3 To set up the fw-1884 in Mackie Emulation protocol 3 iconHow to set up the Behringer bcr2000

To set up the fw-1884 in Cubase or Nuendo 3 To set up the fw-1884 in Mackie Emulation protocol 3 iconScripts. Skill set

To set up the fw-1884 in Cubase or Nuendo 3 To set up the fw-1884 in Mackie Emulation protocol 3 iconP roduct Set-Up Information

To set up the fw-1884 in Cubase or Nuendo 3 To set up the fw-1884 in Mackie Emulation protocol 3 iconOptimal lighting on the set

To set up the fw-1884 in Cubase or Nuendo 3 To set up the fw-1884 in Mackie Emulation protocol 3 iconCalibration Jar Set-up

To set up the fw-1884 in Cubase or Nuendo 3 To set up the fw-1884 in Mackie Emulation protocol 3 iconDatatel Set-Up Instructions

To set up the fw-1884 in Cubase or Nuendo 3 To set up the fw-1884 in Mackie Emulation protocol 3 iconEquipment Set Up Guidelines

To set up the fw-1884 in Cubase or Nuendo 3 To set up the fw-1884 in Mackie Emulation protocol 3 iconHow to set Remote-Viewer using ddns

To set up the fw-1884 in Cubase or Nuendo 3 To set up the fw-1884 in Mackie Emulation protocol 3 iconBlackBerry May Set up Server From in Bangladesh

To set up the fw-1884 in Cubase or Nuendo 3 To set up the fw-1884 in Mackie Emulation protocol 3 iconSmall purchase set-aside (52. 219-4)

To set up the fw-1884 in Cubase or Nuendo 3 To set up the fw-1884 in Mackie Emulation protocol 3 iconSet-Up Instructions and Parts Catalog for




manual




When copying material provide a link © 2017
contacts
manual-guide.com
search