List work and materials related to this section but specified in other sections. Efco recommends that one manufacturer furnish all applicable Division 8 products along with the sunshade device to ensure consistent product quality and compatibility




Download 35.66 Kb.
NameList work and materials related to this section but specified in other sections. Efco recommends that one manufacturer furnish all applicable Division 8 products along with the sunshade device to ensure consistent product quality and compatibility
A typeDocumentation
manual-guide.com > manual > Documentation
SECTION 10 71 13 E-SHADE™ EXTERIOR SUN CONTROL DEVICES
EFCO® Series 5600 Outside Glazed Center Tongue Curtain Wall System
PART 1 GENERAL
1.01 Work Included
A. Furnish and install architectural aluminum curtain wall complete with integral exterior sunshade device and related components as shown on drawings and specified in this section.
B. Sunshade shall be designed as an integral part of EFCO Series 5600 Outside Glazed Curtain Wall System. Other manufacturers requesting approval to bid their product as an equal must submit the following information fifteen days prior to close of bidding.

1. A proposal drawing showing full size details of all sunshade and curtain wall components including all anchors, sunshade supports, and building attachments.

2. Engineering calculations documenting compliance with requirements of Section 1.05.
C. Glass

1. Reference Section 08 81 00 for Glass and Glazing.
D. Single Source Requirement

  1. All products listed in Section 1.02 shall be by the same manufacturer.


List work and materials related to this section but specified in other sections. EFCO recommends that one manufacturer furnish all applicable Division 8 products along with the sunshade device to ensure consistent product quality and compatibility.
1.02 Related Work
A. Section 08 32 13 – Sliding Aluminum – Framed Glass Doors

B. Section 08 41 13 – Aluminum – Framed Entrances and Storefronts

C. Section 08 44 13 – Glazed Aluminum Curtain Walls

D. Section 08 44 33 – Sloped Glazing Assemblies

D. Section 08 51 13 – Aluminum Windows
1.03 Items Furnished but Not Installed
1.04 Items Installed but Not Furnished
1.05 Performance Requirements
A. Sunshade must be designed to resist ___ psf ( ___ Pa) wind load.
B. Sunshade must be designed to resist ___ psf ( ___ Pa) snow load.
C. Sunshade must be designed to resist ___ psf ( ___ Pa) live load (if applicable).
D. Sunshade must be designed to resist ___ lb. concentrated load, in any direction, at any point (if applicable).
1.06 References
1.07 Submittals


  1. Contractor shall submit shop drawings; finish samples, test reports, and warranties.

    1. Samples of materials as may be requested without cost to owner, i.e., metal, glass, fasteners, anchors, frame sections, mullion section, corner section, etc.


1.08 Warranties
A. Total Curtain Wall Installation

1. The responsible contractor shall assume full responsibility and warrant for one year the satisfactory performance of the total curtain wall installation. This includes the glass (including insulated units), glazing, sunshade device anchorage and setting system, sealing, flashing, etc. as it relates to air, water, and structural adequacy and the specifications and approved shop drawings.

2. Any deficiencies due to such elements not meeting the specifications shall be corrected by the responsible contractor at their expense during the warranty period.
Standard warranty period is 3 years, or extended 10 years.

B. Window Material and Workmanship

1. Provide written guarantee against defects in material and workmanship for ___ years from the date of final shipment.
C. Glass

1. as a result of dust or film formation on the internal glass surfaces caused by failure of the hermetic seal due to defects in material and workmanship.

2. Warranty period shall be for 10 (ten) years.
D. Finish

Select for Anodic Finish: Standard warranty period is 3 years, or extended 5 years, or 10 years.

1. Warranty period shall be for ___ years from the date of final shipment.
OR

Select for Organic Finish: Standard warranty period is 5 years, or extended 10 years.

1. Warranty period shall be for ___ years from the date of final shipment.

2. Provide organic finish warranty based on AAMA standard 2604.
OR

Select for Organic Finish: Standard warranty period is 5 years, or extended 10 years, or 15 years, or 20 years.

1. Warranty period shall be for ___ years from the date of final shipment.

2. Provide organic finish warranty based on AAMA standard 2605.
PART 2 PRODUCTS
2.01 Materials
A. Aluminum

  1. Extruded aluminum shall be 6063-T6 alloy and temper.


B. Anchors

1. Perimeter and floor line anchors shall be aluminum or steel. All steel anchors shall be properly insulated from the aluminum.
2.02 Fabrication
A. General

1. All aluminum horizontal extrusions (blades) shall have a minimum wall thickness of .063" (1.5 mm) to .125" (3 mm).

2. Sunshade “arms” and mullion clips shall be extrusions with a nominal wall thickness of .25” (6 mm).


  1. Sunshade Device

1. Horizontal components (blades) shall be mechanically fastened by means of extruded aluminum screw splines.


  1. Finish

See separate finish specification for more details.

  1. Anodic

    1. Finish all exposed areas of aluminum windows and components with electrolytically deposited color in accordance with Aluminum Association Designation

AA-M10-C22-___ Color shall be ___.
Available colors are clear, champagne, light bronze, medium bronze, dark bronze & black.

AA Description Description Arch. Class AAMA Guide Spec.

AA-M10-C22-A41 Clear Anodized 1 611-98

AA-M10-C22-A44 Color Anodized 1 611-98
OR

  1. Organic

    1. Finish all exposed areas of aluminum windows and components with ___. Color shall
      be ___.


High performance 70% PVDF fluoropolymer Ultrapon and 50% PVDF fluoropolymer Ultraflur finishes are available in standard colors. Reference the EFCO color brochure for assistance in color and resin selection. Custom colors are available upon request.

AA Description Description AAMA Guide Spec.

AA-M12-C42-R1X 70% PVDF Ultrapon 2605-98

AA-M12-C42-R1X 50% PVDF Ultraflur2604-98
PART 3 EXECUTION
3.01 Inspection
A. Job Conditions

1. All openings shall be prepared by others to the proper size and shall be plumb, level, and in the proper location and alignment as shown on the architect's drawings.

Inseret at discretion of specifier

2. Provide for manufacturer representation to conduct pre-installation site meeting.
3.02 Installation
A. Use only skilled tradesmen with work done in accordance with approved shop drawings and established specifications, and erect all curtain wall components to all building bench marks and column center lines.
B. Plumb and align curtain wall faces in a single plane for each wall plane, and erect curtain wall materials square and true. Adequately anchor to maintain positions permanently when subjected to normal thermal movement, building movement, and specified wind loads.
C. Adjust windows in curtain wall for proper operation after installation.
D. Furnish and apply sealants to provide a weather tight installation at all joints and intersections and at opening perimeters. Wipe off excess material, leave all exposed surfaces and joints clean and smooth.
3.03 Anchorage


  1. Adequately anchor to maintain positions permanently when subjected to normal thermal movement, specified building movement, and specified wind loads.


3.04 Protection and Cleaning
A. The general contractor shall protect the aluminum materials and finish against damage from construction activities and harmful substances. The general contractor shall remove any protective coatings as directed by the architect, and shall clean the aluminum surfaces as recommended for the type of finish applied.
EFCO is a registered trademark of EFCO Corporation. Ultrapon and Ultraflur are trademarks of EFCO Corporation.
1/14/2014

Share in:

Related:

List work and materials related to this section but specified in other sections. Efco recommends that one manufacturer furnish all applicable Division 8 products along with the sunshade device to ensure consistent product quality and compatibility iconList work and materials related to this section but specified in...

List work and materials related to this section but specified in other sections. Efco recommends that one manufacturer furnish all applicable Division 8 products along with the sunshade device to ensure consistent product quality and compatibility iconThe product is equipped with a low power laser device. To ensure...

List work and materials related to this section but specified in other sections. Efco recommends that one manufacturer furnish all applicable Division 8 products along with the sunshade device to ensure consistent product quality and compatibility icon[Related Sections (where applicable) include the following

List work and materials related to this section but specified in other sections. Efco recommends that one manufacturer furnish all applicable Division 8 products along with the sunshade device to ensure consistent product quality and compatibility iconI. general a. Related documents drawings and general provisions of...

List work and materials related to this section but specified in other sections. Efco recommends that one manufacturer furnish all applicable Division 8 products along with the sunshade device to ensure consistent product quality and compatibility iconGeneral conditons related documents drawings and general provisions...

List work and materials related to this section but specified in other sections. Efco recommends that one manufacturer furnish all applicable Division 8 products along with the sunshade device to ensure consistent product quality and compatibility icon1. 02 Related work specified in other sections

List work and materials related to this section but specified in other sections. Efco recommends that one manufacturer furnish all applicable Division 8 products along with the sunshade device to ensure consistent product quality and compatibility iconPart 1 general 1 Related work in other sections

List work and materials related to this section but specified in other sections. Efco recommends that one manufacturer furnish all applicable Division 8 products along with the sunshade device to ensure consistent product quality and compatibility icon1. 02 Related work covered by other sections of this specification including but not limited to

List work and materials related to this section but specified in other sections. Efco recommends that one manufacturer furnish all applicable Division 8 products along with the sunshade device to ensure consistent product quality and compatibility iconNot Applicable chemical name/class: Oxalic Acid Solution product...

List work and materials related to this section but specified in other sections. Efco recommends that one manufacturer furnish all applicable Division 8 products along with the sunshade device to ensure consistent product quality and compatibility iconSpecifications of the Equipments to be procured: In this specification,...

List work and materials related to this section but specified in other sections. Efco recommends that one manufacturer furnish all applicable Division 8 products along with the sunshade device to ensure consistent product quality and compatibility iconSpecifications of the Equipments to be procured: In this specification,...

List work and materials related to this section but specified in other sections. Efco recommends that one manufacturer furnish all applicable Division 8 products along with the sunshade device to ensure consistent product quality and compatibility iconCongratulations on your purchase of a Celestron microscope. Your...

List work and materials related to this section but specified in other sections. Efco recommends that one manufacturer furnish all applicable Division 8 products along with the sunshade device to ensure consistent product quality and compatibility iconPart 1general 1The requirements of the Contract, Division [1] [01],...

List work and materials related to this section but specified in other sections. Efco recommends that one manufacturer furnish all applicable Division 8 products along with the sunshade device to ensure consistent product quality and compatibility iconOmega Products International, Inc. [Manufacturer] makes no warranty...

List work and materials related to this section but specified in other sections. Efco recommends that one manufacturer furnish all applicable Division 8 products along with the sunshade device to ensure consistent product quality and compatibility iconIn simplest terms, a warranty (also called a guarantee) is an agreement...

List work and materials related to this section but specified in other sections. Efco recommends that one manufacturer furnish all applicable Division 8 products along with the sunshade device to ensure consistent product quality and compatibility iconThe following instructions are given to ensure your safety and prevent...

List work and materials related to this section but specified in other sections. Efco recommends that one manufacturer furnish all applicable Division 8 products along with the sunshade device to ensure consistent product quality and compatibility iconA. Drawings and general provisions of the Contract, including General...

List work and materials related to this section but specified in other sections. Efco recommends that one manufacturer furnish all applicable Division 8 products along with the sunshade device to ensure consistent product quality and compatibility iconFurnish and install as shown on aerco international plans and operation...

List work and materials related to this section but specified in other sections. Efco recommends that one manufacturer furnish all applicable Division 8 products along with the sunshade device to ensure consistent product quality and compatibility iconThank you for choosing this TeckNet product. To ensure optimum performance...

List work and materials related to this section but specified in other sections. Efco recommends that one manufacturer furnish all applicable Division 8 products along with the sunshade device to ensure consistent product quality and compatibility iconFurnish and deliver all environmental idn active infrared cameras...




manual




When copying material provide a link © 2017
contacts
manual-guide.com
search