Note: The chrome cover holds the filter and the velocity stack in place. Install the chrome cover with three hex head bolts. Tip




Download 11.72 Kb.
NameNote: The chrome cover holds the filter and the velocity stack in place. Install the chrome cover with three hex head bolts. Tip
A typeDocumentation
manual-guide.com > manual > Documentation


2008 & UP FLH

MoFlow Air Filter Assembly

Instructions
California Air Resource Board EO# D-668

Legal for use in California


  1. Remove the stock air cleaner and crankcase breather hardware. Refer to the manufacturer service manual.

  2. Remove the black metal plate that connects the throttle body to the heads and discard

  3. Clean the carburetor inlet face and both the crankcase breather o-ring surfaces. Remove all dust and/or grease.

  4. Install gasket supplied with the new kit. Be careful to line up all the holes.

  5. Locate the new base assembly. Be sure the four o-rings are installed in the grooves. Tip: If the o-rings do not stay in the grooves a small amount of grease can be applied to the o-ring to keep it in place for installation.

  6. Install the base assembly with two banjo bolts and six flat washers (stack two washers between the breather block and the head and one between the breather bolt head and the breather block, but do not tighten the banjo bolts fully at this time. Just Look at the instructions.

  7. Install three button head bolts through the base into the throttle body.

Note: Fuel injection applications may require loosening the intake manifold for proper alignment. (Be sure to retighten after alignment.)

  1. Torque the button head bolts to 3-5 ft-lbs (36-60 in-lbs) and the banjo bolts to 10-12 ft-lbs (120-144 in-lbs).

  2. Install the aluminum velocity stack onto the base. Note: The velocity stack is a slip fit.

  3. Install the Air Aide air filter element. Note: The chrome cover holds the filter and the velocity stack in place.

  4. Install the chrome cover with three hex head bolts.

Tip: Do not force the cover in place. Check the Filter and Velocity Stack for proper location.

  1. Torque the hex head bolts to 3-5 ft-lbs (36-60 in-lbs).


Tip: Use of “Loctite” is required with this kit. Two drops should be applied to every bolt just before the bolt is to be installed!!
DO NOT INSTALL THIS UNIT WITHOUT APPLYING LOCKTITE

TO EVERY SCREW, NUT OR BOLT!!

Note: *After this installation it is recommended that the engine air fuel ratio be checked.

*Fuel injected models are to be remapped accordingly within California (CARB) guidelines using an

approved remapping device.

*Check ALL the fasteners every 2500 miles for proper torque.
Our Warranty Policy

Cycle Visions’ obligation under “Our Warranty Policy” is limited to one (1) year from date of purchase to repair or replacement of the defective item (s). Chrome, polished, powder-coated, anodized finishes, or electrical parts are limited to thirty (30) day from date of purchase.
This warranty will be void on all products that show evidence of misapplication, improper installation, abuse, lack of proper maintenance, negligence, or alteration from their original design.
The consumer will be responsible for removing from the vehicle any defective item (s), transportation costs prepaid and for reinstallation upon return by Cycle Visions. The loss of use of the product, loss of time, inconvenience, commercial loss or consequential damages is not covered. Cycle Visions reserves the right to change the design of any product without assuming any obligation to modify any product previously manufactured. Warranty returns of Cycle Visions products are few because of our high quality products.
Carefully inspect all parts…. If you find that your parts arrived in damaged conditional all original packaging material (box and other materials) must be saved to make a proper damage claim within seven (7) days. You must be able to present the damaged boxes and materials to the freight carrier to verify your claim. The user shall assume all legal, personal, injury risk and liability and all other obligations, duties and risks associated therewith.

Cycle Visions™


San Diego, California (619) 295.7800

www.cyclevisions.com

See our other products on the web!

Made in the USA




Rev 06/12

Share in:

Related:

Note: The chrome cover holds the filter and the velocity stack in place. Install the chrome cover with three hex head bolts. Tip icon2号:Chrome Rear Fog light lamp Cover Trim Fits 2014 2015 Mazda 3 Axela Hatchback

Note: The chrome cover holds the filter and the velocity stack in place. Install the chrome cover with three hex head bolts. Tip iconC2c grille Insert Overlay (3 pc) Chrome Plated 2016-2017. Lund 958186...

Note: The chrome cover holds the filter and the velocity stack in place. Install the chrome cover with three hex head bolts. Tip icon[5152: 4884: 1004/163710: verbose1: service main cc(36)] Service...

Note: The chrome cover holds the filter and the velocity stack in place. Install the chrome cover with three hex head bolts. Tip icon02-May-2011 8: 16: 22 am copied Bookmarks from C:\Users\jmf\AppData\Local\Google\Chrome\User...

Note: The chrome cover holds the filter and the velocity stack in place. Install the chrome cover with three hex head bolts. Tip iconSupply and install one 18” (450 mm) diameter culvert for driveway,...

Note: The chrome cover holds the filter and the velocity stack in place. Install the chrome cover with three hex head bolts. Tip iconCmw+ 1 Installation Cover Letter (cmw435c doc) 0 The purpose of this...

Note: The chrome cover holds the filter and the velocity stack in place. Install the chrome cover with three hex head bolts. Tip iconChrome for linux mint 18

Note: The chrome cover holds the filter and the velocity stack in place. Install the chrome cover with three hex head bolts. Tip iconChrome for linux mint

Note: The chrome cover holds the filter and the velocity stack in place. Install the chrome cover with three hex head bolts. Tip iconThe Chrome Borne by Mercedes Lackey

Note: The chrome cover holds the filter and the velocity stack in place. Install the chrome cover with three hex head bolts. Tip iconHow to download google chrome for xbox 360

Note: The chrome cover holds the filter and the velocity stack in place. Install the chrome cover with three hex head bolts. Tip iconWorks Cited "3 Ways Your Students Can Use Google Chrome."

Note: The chrome cover holds the filter and the velocity stack in place. Install the chrome cover with three hex head bolts. Tip icon[Note] Do not place any items in the airbag. Please do not install...

Note: The chrome cover holds the filter and the velocity stack in place. Install the chrome cover with three hex head bolts. Tip iconAbstract fir filter is an important part of the digital filter. The...

Note: The chrome cover holds the filter and the velocity stack in place. Install the chrome cover with three hex head bolts. Tip iconCover page

Note: The chrome cover holds the filter and the velocity stack in place. Install the chrome cover with three hex head bolts. Tip iconNever judge a book by its cover.”

Note: The chrome cover holds the filter and the velocity stack in place. Install the chrome cover with three hex head bolts. Tip iconHotel cover letter sample

Note: The chrome cover holds the filter and the velocity stack in place. Install the chrome cover with three hex head bolts. Tip iconTest report cover sheet

Note: The chrome cover holds the filter and the velocity stack in place. Install the chrome cover with three hex head bolts. Tip iconTest report cover sheet

Note: The chrome cover holds the filter and the velocity stack in place. Install the chrome cover with three hex head bolts. Tip iconTest report cover sheet

Note: The chrome cover holds the filter and the velocity stack in place. Install the chrome cover with three hex head bolts. Tip icon6 Required Credit Cover Coverage Analysis 23




manual




When copying material provide a link © 2017
contacts
manual-guide.com
search